Driveshaft Shop - Google My Business Category Analyze

Question: Lookin for a drive shaft for 2004 Chevrolet Avalanche 1500 2wd 8.3 engine.... can u help me
Author: Spade Gang

Answer: If they don't have one in stock they can rebuild yours.
Answer: Give Driveshaftpro a call

Question: Do you cut driveshaft and weld and balance
Author: Felipe Cardenas

Answer: Yes Felipe, we can do all of the above. Feel free to bring it in any time M-F 8am-5pm and ask for Adrian. Thanks!
Answer: yes se do. If yuo need new one se do
Answer: yes that's what I had done. We live in a society that instead of making a phone call and having answer from shop in seconds people look online for answers.

Question: (Translated by Google) I need to understand my arrow of my silverado I have to take the truck or just the arrow (Original) Necesito entender mi flecha de mi silverado tengo que llevar la camioneta o sólo la flecha
Author: Arturo Cardenas

Question: Do you straighten drive lines.
Author: Christa Wolfe

Question: I'm dropping a 302 and aod in a 64 custom 500, 4 door. What driveshaft will I need and what will it cost. I'm doing all this work in a gravel driveway..lol...so any help is greatly appreciated!
Author: Dennis Williams

Answer: Here's what I would do based on dropping a T5, 5.0 & EFI into my '67 Mustang. This is assuming you're not making 600hp or using slicks that might twist a stock driveshaft or break stock size u-joints 1) Install the engine and trans 2) Measure the driveshaft length you need and type of transmission yoke (google instructions if needed) 3) See if a stock Ford driveshaft from your car or another Ford is the right length within an inch or so, or even longer 4) You might look at a crown vic, 80's thunderbird or cougar, F150 Then do one of the following 1) Consider buying a new, stock length driveshaft if one fits 2) Ask your driveshaft shop how much to shorten and balance a used driveshaft. Look for a straight used drive shaft longer than you need at a wrecking yard 3) Take your measurement to the shop and get a full custom driveshaft (most expensive)

Question: what is the best gears for a 2018 tacoma 4x4 with 33 inch tires?
Author: A Google User

Question: Does anyone in Kingman work on bicycle batteries In Kingman Az???
Author: Steve Robinett

Question: Do u charge to check a drive line
Author: Brenda Langston

Question: Can you do special drive lines
Author: James Alldredge

Answer: Yes
Answer: Yes

Question: I am told that my 2008 solara toyota needs to have the front axle replaced because the boot is busted. Can you give me an approximate price to do that and how long it will take. Please.
Author: mike donahue

Answer: You would have to go to their website or even contact them on the phone to get an estimate for that particular job
Answer: I agree do not go there. I had a horrible experience. They ended up rebuilding my specialty vehicle completely wrong and caused more problems. Worst thing was when I questioned them, they just acted like it was normal when it left. Children work here.
Answer: Go anywhere but there. They are irresponsible children. I wouldn't direct my worst enemy there.

Question: I have a two piece drive shaft out of a C10 long bed it is a foot too long can I cut it and use it
Author: Mac Canales

Answer: Phoenix rack will instruct you regarding how to measure; then, cut the shaft to size. Balancing is optional.
Answer: I am sure they could do that for you, but they are not going to tell you how to do it yourself. They make their living by using their knowledge to make a paycheck to support their families.

Question: Do, or can you rebuild CV axles?
Author: UnusedAgent 6C37L

Question: Do they have public restrooms?
Author: Rachel Smith

Question: hallo, how much is the cost for drive shaft balance
Author: julio garcia

Question: Do you guys do after hours vehicle drop off?
Author: Paetyn Wilson

Answer: They close at 5pm and therr is usually no one there to receive your keys.
Answer: Hello Paetyn. Our hours are M-F 7am to 5pm. We do have a mail slot in Door #3 that you can drop your keys in after hours just let us know ahead of time :) Lisa
Answer: Probably not, but I would call and ask

Question: Yea my dad purchase a front axle for a gmc safari awd. When after driving it, it started to make a pop or a clunking sound when I turned? How much well cost to rebuild that front axle?
Author: Torrey Russell

Answer: What is the ball park price to balance a drive shaft from an 82 El camino Ujoints are ok..How long will you have it and do I need an appointment? Thanks.. Larry.
Answer: Call and talk with Kyle he will get it figured out.
Answer: I would say call them to schedule a time for diagnosis. Depends on what's wrong and how much the parts are that go into fixing

"The quality of work, experience, and attention to detail is impeccable."

"Great Prices, Great Service, & Knowledged Peeps!!!!"

"Price was fair and the job was done quickly!!"

"Adrian provided me with excellent service."

"Management or owner not sure.takes work can't finish on time"

"They staff was also very helpful and friendly."

"Really good people, Top notch service, Quality Products."

"Quick service and quality work."

"They are really, good workmanship and relatively fast turn around time."

"Very good experience clean shop the worker is very cooperative very good service"

"Great guy, great work, great prices"

"Great place very knowledgeable"

"Inland Empire said yes, go to the corona location they will help you."

"Melinda is one of kind, patient & customer service oriented."

"Well trained and detailed work experience and an awesome customer service team."

"Kyle was great got it done quickly very inexpensive and great service."

"I highly recommend their products and OUTSTANDING customer service."

"Very friendly and knowledgeable people."